Searching for cordless power tools made in USA today can be time-consuming. (Below) after researching, I have put together a helpful list with pictures of cordless power tools made in the USA and why professionals prefer them and are conveniently available online.
Craftsman & Milwaukee Cordless Power Tools Made in USA
DeWalt Cordless Power Tools Made in USA
Makita Cordless Power Tools Made in USA
Paslode Cordless Power Tools Made in USA
Hoover Commercial Cordless Tools Made in USA
Related Pressure washers made in USAFor more on pressure washers made in USA read the full article.
6 Reasons Why Pros Prefer Paslode XP Cordless Framing Nailer
The Paslode XP Cordless Framing Nailer has been designed, built, tested, and proven to get the job done right.
Related Air compressors made in USAFor more on air compressors made in USA read the full article.
Here are six reasons why,
The Paslode XP fuel system provides constant power for driving nails flush into even the most complicated wood.
This cordless nailer’s fuel system gives you 9,000 shots per full battery charge.
And 1,200 shots per fuel cell to keep you productive and able to tackle the most challenging jobs all day long.
Related Garden hoses made in USAFor more on garden hoses made in USA read the full article.
This tool will stand up to wear and tear like no other and outlast any other cordless woodworking nailer.
The XP is the lightest cordless nailer on the market.
It gives you better maneuverability and less fatigue because it weighs only 7.2 lbs, even lighter than most pneumatic framing nailers.
Related Pellet grills made in USAFor more on pellet grills made in USA read the full article.
5. Best in Class Features
The XP id loaded with best-in-class features, including:
- Tool-less adjustable nailing depth.
- Faster nail loading with bypass follower.
- An easy to insert and remove battery.
- Superior comfort and control with improved ergonomics and maneuverability.
- An increased fan for enhanced cooling and increased productivity.
Related Zero-Turn mowers made in USAFor more on zero-turn mowers read the full article.
The XP is built for maximum productivity in a wide variety of applications, including:
- Floor joists.
- Roof decks.
- Truss attachment and more.
Related Bottle Jacks made in USAFor more on bottle jacks made in USA read the full article.
6. Power Fuel System
The XP runs on a fuel cell system, which is better than the battery alone.
And here’s why,
Fuel cell power means no heavy battery, making Paslode cordless nailers the lightest on the market.
Related Floor fans made in USAFor more on floor fans made in USA read the full article.
The more straightforward mechanism means fewer heavy parts, less maintenance, and less complicated wiring that can break.
Plus, the all-season framing fuel cell keeps you working even in temperatures as low as 14 degrees.
And when you combine Paslode nailers with genuine, high-quality Paslode nails explicitly designed for the fuel system, you get performance and productivity that never lets up.
Related Jumper cables made in USAFor more on jumper cables made in USA read the full article.
How to Set Up a Paslode XP Cordless Framing Nailer
The XP is easier to set up and allows you to work quickly and be more productive.
In three easy steps,
- Insert the battery and insert the fuel cell.
- Then load the nails.
- Pull the bypass follower back and release it into the nail strip.
Professionals choose Paslode because it is the best cordless nailer to get the job done right and build their reputation.
How to Use a DeWalt 20v XR Hammer Drill (In 6 easy steps)
(Below) I will cover six easy steps on adjusting the speed correctly, torque, and clutch settings on a DeWalt 20v XR Cordless Hammer Drill.
Always refer to the manual for any additional operating instructions.
1. Remove the Battery
When you pick up the tool, the first thing you should do is remove the battery to see the different operations of the tool.
2. Speed Setting
The DeWalt 20v XR Hammer Drill DCD996 model typically has a three-speed transmission setting on top of the tool.
- Speed 3: Is for applications requiring high speed and low torque.
- Speed 2: Is for applications requiring medium speed and more torque and control.
- Speed 1: Is for applications requiring a very slow speed and high torque.
3. Adjust the Clutch
The clutch setting is located at the front of the tool and has one to eleven options.
The one to eleven settings allows the tool to determine how much resistance it will need to stop the tool.
For example, if you are trying to install a small screw in a hinge, and you want to make sure you don’t overdrive the screw.
In this case, you can lower the clutch collar to one of the lower settings one, two, or three.
This way, the tool needs very little resistance to stop turning, and the screw is not overloaded.
If, for example, you have a more demanding application, say a more significant fastener, or you need to drill a giant hole.
In that case, you can adjust the clutch collar much higher so that the tool needs more resistance to stop.
4. Drill Mode
A drill mode is also represented by a small drill bit icon on the tool.
The drill mode will disengage the clutch and allow the tool to continue to operate.
Important note, when operating this tool, always use the side handle of the tool.
5. Hammer Mode
Another popular setting for this tool is the hammer drill mode.
The hammer drill setting is located right next to the drill icon.
You can turn the clutch collar one more time so that the arrow lines up with the little hammer icon on the tool.
The hammer setting will allow the tool to strike while also rotating to drill different masonry applications.
In addition, the hammer mode will disengage the clutch as well.
As I mentioned before, make sure you have control of the tool by using the side handle and the variable speed trigger.
The variable speed trigger is essential because the tool will not stop in drill or hammer mode.
6. Install the Side Handle
To install the side handle on the tool, slide it over the collar and start turning the handle to tighten it.
Once the handle is installed, you can reinstall the battery into the tool.
You can then efficiently operate the tool with two hands.
Unbelievable Makita 36v Cordless Right Angle Drill Features
The Makita 36v cordless right-angle drill has unique features to make your job easier.
Here’s why in a nutshell,
This tool comes with a multi-position front handle that allows you to perform from different positions.
In addition, the tool also has an auxiliary side handle that can be mounted on both sides.
Inside, this tool has its two speeds 1400-rpm on high and 350-rpm on low.
And in coordination with the gearbox, it also has an automatic torque unit built into the tool.
As I mentioned earlier, it is essential to reduce the speed when using this tool for heavy torque applications as the automatic torque feature will be very useful for these types of applications.
This right angle drill also has a variable speed on the trigger, so, again, depending on the application, you can start nice and slow to get high accuracy.
For increased accuracy, this tool is equipped with an LED light on the bottom that gives you better visibility of what you are working on.
The chuck key is stored on the side of the tool for easy access and convenience.
This Makita 36v cordless right angle drill is an excellent addition to your toolbox, primarily if you work in high-torque drilling applications daily.
How Milwaukee Power Tools Became Popular From Day One
The Milwaukee power tool company has a fascinating history and was founded in 1924.
Related Brand of tools list made in USAFor more on brand of tools list made in USA read the full article.
Its goal was to produce the ideal power tools and accessories for professionals.
After World War I, Ford’s founder, Henry Ford, was looking for a portable quarter-inch power drill for his workers on the assembly line.
Milwaukee rose to the challenge and created the hole shooter, the first lightweight, portable quarter-inch drill.
The Milwaukee drill revolutionized the industry and greatly improved Ford’s and Milwaukee’s business.
Over the years, Milwaukee began to manufacture its motors and parts to improve its design significantly.
They became lighter, more powerful, and durable.
Because of these improvements, Milwaukee quickly earned a reputation for quality.
Other industries eventually turned to Milwaukee to improve their tools as well.
They improved the grinder sander with a spring clutch and circular saw designs.
Then, in 1949, Milwaukee came out with a new tool: the half-inch right angle drill.
The right-angle drill was handy to electricians and plumbers because it could easily fit between studs to drill holes for conduits and pipes.
The company also invented the Sawzall, the first reciprocating saw.
Thanks to the blades Milwaukee devised, it could cut a wide variety of materials, perfect for demolition and other rough-cutting applications.
During the 1950s and 1960s, the home building industry in the United States began to flourish, and Milwaukee expanded its business.
In 1967 they brought out an improved portable band saw and began their long history in the metalworking industry.
In the 1970s, they also brought out new products such as the hole hawg, the magnum hole shooter, the four-and-a-half-inch grinder, and the super Sawzall.
In 1999 Milwaukee created the seven-and-a-quarter-inch circular saw, a lighter, more powerful, and more accessible-to-use version.
Until that time, cordless tools did not have good battery life and did not last very long.
Milwaukee didn’t want to get too serious about cordless tools until they were good enough for their professional market.
So they waited until 2005 to bring out their lithium-ion battery technology, and the company continued to expand their offerings by bringing out more cordless tools.
In 2007 Milwaukee began to focus on disruptive innovation and split its focus into different trades and sectors, including:
Instead of guessing what its customers wanted, Milwaukee sent people out into the field to get feedback from real professionals.
Company officials let people in the field test prototypes of their new products before they went into mass production.
They still do this today because this technique created the M12 line, specialty tools, and a new hand tool division.
In 2010 Milwaukee created RED-LITHIUM® technology.
RED-LITHIUM® technology improved their batteries by 40%, and later the company went on to invent fuel technology.
At the same time, fuel technology takes its RED-LITHIUM® to the next level in three ways.
- First: Battery capacity is increased.
- Second: The electric motor and the tool are improved.
- And lastly: Computer chips are installed to communicate between the tool and the battery, improving energy consumption.